Walvis Bay 2-4-2T Hope
Type and origin
Power type Steam
Designer Kerr, Stuart and Company
Builder Kerr, Stuart and Company
Serial number 652
Build date 1899
Total produced 1
Configuration:
• Whyte 2-4-2T (Columbia)
• UIC 1B1n2t
Driver 2nd coupled axle
Gauge 2 ft 6 in (762 mm) Namaqualand
Leading dia. 14 in (356 mm)
Coupled dia. 24 in (610 mm)
Trailing dia. 14 in (356 mm)
Frame type Plate
Loco weight 12 LT (12,190 kg)
Fuel type Coal
Fuel capacity 5 long hundredweight (0.3 t)
Water cap 100 imp gal (455 l)
Firebox type Round-top
• Firegrate area 3.5 sq ft (0.33 m2)
Boiler:
• Diameter 2 ft 1 in (635 mm)
• Tube plates 5 ft 1 in (1,549 mm)
• Small tubes 36: 1 3?4 in (44 mm)
Boiler pressure 120 psi (827 kPa)
Heating surface 102 sq ft (9.5 m2)
Cylinders Two
Cylinder size 6 in (152 mm) bore
10 in (254 mm) stroke
Valve gear Stephenson
Valve type Murdoch's D slide
Couplers Buffers-and-chain
Performance figures
Tractive effort 1,020 lbf (4.5 kN) @ 75%
Career
Operators Walvis Bay Railway
Number in class 1
Official name Hope
Delivered 1899
First run 1899
Disposition Plinthed at Walvis Bay station
The Walvis Bay 2-4-2T Hope of 1899 was a South African steam locomotive from the pre-Union era in the Cape of Good Hope.
In 1899, the Walvis Bay Tramway in the British territory of Walvis Bay, a Cape of Good Hope exclave in German South West Africa, placed a single tank locomotive with a 2-4-2 Columbia type wheel arrangement in service. It remained in service until 1915, when a Cape gauge railway was opened between Swakopmund and Walvis Bay.
Walvis Bay Tramway
The British territory surrounding the port of Walvis Bay in Deutsch-Sudwest-Afrika (DSWA), an enclave with an area of 434 square miles (1,124 square kilometres), was administered as part of the Cape of Good Hope. The Walvis Bay railway began as a 2 ft 6 in (762 mm) gauge horse-drawn tramway within the confines of the harbour town. The gauge was most probably selected to ensure a wide enough path for horses between the rails, as was probably also the case on the light mule-drawn Namaqualand Railway which was built to the same gauge between Port Nolloth and O'kiep in northwestern Cape of Good Hope.
Manufacturer
In June 1899, a single small side-tank locomotive with a 2-4-2 Columbia type wheel arrangement was shipped from Kerr, Stuart and Company of Stoke-on-Trent in England. It arrived in Walvis Bay on 22 August 1899 aboard the barque Primera, along with a distilling plant, railway trucks and 200 tons of coal. The engine was named Hope and was placed in service on the short Walfish Bay Tramway.
The locomotive was a standard Sirdar class engine, similar to the two Class NG1 0-4-0T locomotives which were to enter service on the Bezuidenhout Light Railway a year later during the Second Boer War, but with leading and trailing pony wheels added and a tropical cab roof. Kerr, Stuart was a supplier of contractor's engines and often built locomotives to standard designs, but without frame stretchers and axles. These semi-completed locomotives were kept in stock until an order was placed. This allowed them to be delivered with a minimum of delay.
Characteristics
The engine was built on 5.8 inch (16 millimetres) thick plate frames, arranged outside the coupled wheels. It had a boiler with an inside diameter of 2 feet 1 inch (635 millimetres), set at an operating pressure of 120 pounds per square inch (827 kilopascals). Its inclined cylinders were arranged outside the plate frames and had a bore of 6 inches (152 millimetres) and a 10 inches (254 millimetres) stroke. It used Murdoch's D type slide valves, actuated by Stephenson valve gear through rocker arms.
It had coupled wheels of 24 inches (610 millimetres) diameter. The coal bunker had a capacity of 5 long hundredweight (0.3 tonnes) and the side-tanks had a water capacity of 100 imperial gallons (455 litres). The total weight of the engine in full working order was 12 long tons (12,190 kilograms) and it had a tractive effort of 1,020 pounds-force (4.5 kilonewtons) at 75% of boiler pressure.
Walvis Bay Railway
In 1899, the Cape government began to extend the tramway as a railway to a terminus named Plum, 11 miles (18 kilometres) due east of Walvis Bay near Rooibank, essentially in the middle of the Namib desert on the DSWA border. The decision to build the 12-mile long (19-kilometre) railway between the harbour and the international border with DSWA followed the start of construction of the Swakopmund-Windhuk Staatsbahn in DSWA in 1897 and was an attempt to not forfeit freight trade opportunities into the interior once that line was completed.
The object with the railway was to bridge the region of shifting sand dunes between the harbour and the interior so that goods could be forwarded by rail to Plum and then by ox wagon from there into the interior. The extension was completed in 1903, but saw very limited use, mainly to obtain firewood and to render possible the occasional picnic in the desert.
Service
The engine Hope operated on the railway for some five years, until it became apparent by 1904 that the short link had no economic benefit. In March 1905, the Acting Magistrate reported an income over two years of ?39 against expenditure of 1,200 Pounds. By then, sections of track of more than 1?2 mile (0.8 kilometres) had been buried during a sandstorm under 30 feet (9 metres) high dunes.
The main reason for the abandonment of the railway was the opening of the copper mines at Tsumeb and the construction of the Otavi Railway, which commenced in November 1903 to connect Tsumeb with the port of Swakopmund, just north of the DSWA border. The locomotive continued to work the 3 miles (5 kilometres) of remaining track in and about the settlement, working cargo in the harbour and removing insanitary rubbish to a safe distance from the village.
Preservation
After a Cape gauge railway was opened between Swakopmund and Walvis Bay in March 1915, the locomotive remained stored in a local siding in Walvis Bay for years, until it was repaired for preservation by the South African Railways administration and plinthed in Windhoek during the 1940s. It was returned to Walvis Bay in 1963, to be plinthed at Walvis Bay railway station. To protect it against Walvis Bay's notoriously corrosive sea air, the engine has since been enclosed in a glass cage.
YouTube: Exploring Namibia TV
Purchase photo/4K video: portfolio1 portfolio2
Aerial photo/video service/inquiries: info@traveltonamibia.com
No comments:
Post a Comment